Current as of: Oct. 2009
(a)(1) Oil-piping systems for the transfer or discharge of cargo or fuel oil must be separate from other piping systems as far as practicable, and positive means shall be provided to prevent interconnection in service.
(2) Fuel oil and cargo oil systems may be combined if the cargo oil systems contain only Grade E oils and have no connection to cargo systems containing grades of oil with lower flash points or hazardous substances.
(3) Pumps used to transfer oil must have no discharge connections to fire mains, boiler feed systems, or condensers unless approved positive means are provided to prevent oil from being accidentally discharged into any of the aforementioned systems.
(b) When oil needs to be heated to lower its viscosity, heating coils must be properly installed in each tank.
(1) Each drain from a heating coil as well as each drain from an oil heater must run to an open inspection tank or other suitable oil detector before returning to the feed system.
(2) As far as practicable, no part of the fuel-oil system containing heated oil under pressure exceeding 180 KPa (26 psi) may be placed in a concealed position so that defects and leakage cannot be readily observed. Each machinery space containing a part of the system must be adequately illuminated.
(c) Filling pipes may be led directly from the deck into the tanks or to a manifold in an accessible location permanently marked to indicate the tanks to which they are connected. A shutoff valve must be fitted at each filling end. Oil piping must not be led through accommodation spaces, except that low pressure fill piping not normally used at sea may pass through accommodation spaces if it is of steel construction, all welded, and not concealed.
(d) Piping subject to internal head pressure from oil in the tank must be fitted with positive shutoff valves located at the tank.
(1) Valves installed on the outside of the oil tanks must be made of steel, ductile cast iron ASTM A 395 (incorporated by reference; see 46 CFR 56.01-2), or a ductile nonferrous alloy having a melting point above 1,700 [deg]F and must be arranged with a means of manual control locally at the valve and remotely from a readily accessible and safe location outside of the compartment in which the valves are located.
(i) In the special case of a deep tank in any shaft tunnel, piping tunnel, or similar space, one or more valves must be fitted on the tank, but control in the event of fire may be effected by means of an additional valve on the piping outside the tunnel or similar space. Any such additional valve installed inside a machinery space must be capable of being operated from outside this space.
(ii) [Reserved]
(2) If valves are installed on the inside of the tank, they may be made of cast iron and arranged for remote control only. Additional valves for local control must be located in the space where the system exits from the tank or adjacent tanks. Valves for local control outside the tanks must be made of steel, ductile cast iron ASTM A 395 , or a ductile nonferrous alloy having a melting point above 1,700 [deg]F.
(3) Power operated valves installed to comply with the requirements of this section must meet the following requirements:
(i) Valve actuators must be capable of closing the valves under all conditions, except during physical interruption of the power system (e.g., cable breakage or tube rupture). Fluid power actuated valves, other than those opened against spring pressure, must be provided with an energy storage system which is protected, as far as practicable, from fire and collision. The storage system must be used for no other purpose and must have sufficient capacity to cycle all connected valves from the initial valve position to the opposite position and return. The cross connection of this system to an alternate power supply will be given special consideration by the Marine Safety Center.
(ii) The valve shall have a local power actuator to both open and close the valve unless local manual opening operation will not prevent remote closing of the valve.
(iii) The positioning of the valve by either the local or remote actuators shall not void the ability of the other actuator to close the valve.
(iv) The valve shall be provided with a means of emergency manual operation to both open and close the valve regardless of the status of the power operating system. Such manual operation may interfere with the power operation, and if so, shall be protected from causal use by means of covers, locking devices, or other suitable means. Instructions and warnings regarding the emergency system shall be conspicuously posted at the valve.
(4) Remote operation for shutoff valves on small independent oil tanks will be specially considered in each case where the size of tanks and their location may warrant the omission of remote operating rods.
(e) Fuel oil tanks overhanging boilers are prohibited.
(f) Valves for drawing fuel or draining water from fuel are not permitted in fuel oil systems except that a single valve may be permitted in the case of diesel driven machinery if suitably located within the machinery space away from any potential source of ignition. Such a valve shall be fitted with a cap or a plug to prevent leakage.
(g) Test cocks must not be fitted to fuel oil or cargo oil tanks.
(h) Oil piping must not run through feed or potable water tanks. Feed or potable water piping must not pass through oil tanks.
(i) Where flooding equalizing cross-connections between fuel or cargo tanks are required for stability considerations, the arrangement must be approved by the Marine Safety Center.
(j) Piping conveying oil must be run well away from hot surfaces wherever possible. Where such leads are unavoidable, only welded joints are to be used, or alternatively, suitable shields are to be fitted in the way of flanged or mechanical pipe joints when welded joints are not practicable. Piping that conveys fuel oil or lubricating oil to equipment and is in the proximity of equipment or lines having an open flame or having parts operating above 500 [deg]F must be of seamless steel. (See Sec. 56.50-65 of this part.)
(k) Oil piping drains, strainers and other equipment subject to normal oil leakage must be fitted with drip pans or other means to prevent oil draining into the bilge.
(l) Where oil piping passes through a non-oil tank without stop valves complying with paragraph (d) of this section installed at all tank penetrations, the piping must comply with Sec. 56.50-50(k).
(m) Each arrangement for the storage, distribution, and use of oil in a pressure-lubrication system must--
(1) As well as comply with Sec. 56.50-80, be such as to ensure the safety of the vessel and all persons aboard; and
(2) In a machinery space, meet the applicable requirements of Sec. Sec. 56.50-60 (b)(2) and (d), 56.50-85(a)(11), 56.50-90 (c) and (d), and 58.01-55(f) of this subchapter. No arrangement need comply with Sec. 56.50-90 (c)(1) and (c)(3) of this subchapter if the sounding pipe is fitted with an effective means of closure, such as a threaded cap or plug or other means acceptable to the Officer in Charge, Marine Inspection. The use of flexible piping or hose is permitted in accordance with the applicable requirements of Sec. Sec. 56.35-10, 56.35-15, and 56.60-25(c).
(n) Each arrangement for the storage, distribution, and use of any other flammable oil employed under pressure in a power transmission-system, control and activating system, or heating system must be such as to ensure the safety of the vessel and all persons aboard by--
(1) Complying with Subpart 58.30 of this subchapter; and,
(2) Where means of ignition are present, meeting the applicable requirements of Sec. Sec. 56.50-85(a)(11), 56.50-90 (c) and (d), and 58.01-55(f) of this subchapter. Each pipe and its valves and fittings must be of steel or other approved material, except that the use of flexible piping or hose is permitted in accordance with the applicable requirements of Sec. Sec. 56.35-10, 56.35-15, and 56.60-25(c).
[CGFR 68-82, 33 FR 18843, Dec. 18, 1968, as amended by CGFR 69-127, 35 FR 9979, June 17, 1970; CGD 73-254, 40 FR 40165, Sept. 2, 1975; CGD 77-140, 54 FR 40609, Oct. 2, 1989; 55 FR 39968, Oct. 1, 1990; CGD 83-043, 60 FR 24774, May 10, 1995; USCG-2000-7790, 65 FR 58460, Sept. 29, 2000; USCG-2004-18884, 69 FR 58346, Sept. 30, 2004; USCG-2003-16630, 73 FR 65178, Oct. 31, 2008]________________________________________________________________________
State Laws: Watercraft| Alabama | Alabama Code > Title 33 > Chapter 5 - Registration And Operation Of Vessels | | Alabama Code > Title 33 > Chapter 6 - Discharge Of Litter And Sewage From Watercraft | | Alabama Code > Title 33 > Chapter 6A - Recreational Vessel And Residence Boat Sewage Discharges Regulated | | Alaska | Alaska Statutes Chapter 05.25 - Watercraft | | Alaska Statutes Chapter 30.30 - Abandoned And Derelict Vessels | | Arizona | Arizona Laws > Title 5 > Chapter 3 - Boating And Water Sports | | California | California Harbors and Navigation Code > Division 3 - Vessels | | California Harbors and Navigation Code > Division 4 - Masters, Crews And Cargoes | | California Harbors and Navigation Code > Division 5 - Pilots For Monterey Bay And The Bays Of San Francisco, San Pablo, And Suisun | | Connecticut | Connecticut General Statutes > Title 15 > Chapter 268 - Boating | | Delaware | Delaware Code Title 23 > Chapter 21 - Motorboats | | Delaware Code Title 23 > Chapter 22 - Boating Safety | | Delaware Code Title 23 > Chapter 23 - Operation Of A Vessel Or Boat While Under The Influence Of Intoxicating Liquor And/Or Drugs | | Delaware Code Title 23 > Chapter 24 - Exemptions From Civil Liability For Rendering Vessel Traffic Information Services | | Florida | Florida Statutes > Title XXIV - Vessels | | Florida Regulations Chapter 61B-60 - Yacht and Ship Brokers | | Florida Regulations > Division 68D - Vessel Registration and Boating Safety | | Idaho | Idaho Code Title 67 > Chapter 70 - Idaho Safe Boating Act | | Illinois | Illinois Compiled Statutes > 625 ILCS 45 - Boat Registration and Safety Act | | Indiana | Indiana Code > Title 9 > Article 31 - Watercraft Titling And Registration | | Indiana Code > Title 25 > Article 28 - Boat Pilots | | Kansas | Kansas Statutes > Chapter 32 > Article 11 - Boating And Water Activities | | Maine | Maine Revised Statutes > Title 10 > Chapter 204-B - Watercraft Manufacturers, Distributors And Dealers | | Maine Revised Statutes > Title 10 > Chapter 212-A - Maine Marina And Boatyard Storage Act | | Maine Revised Statutes > Title 10 > Chapter 627 - Vessels | | Maine Revised Statutes > Title 12 > Chapter 935 - Watercraft And Airmobiles | | Maine Revised Statutes Title 23 > Chapter 412 - Waterborne Transportation | | Massachusetts | Massachusetts General Laws > Part I > Title XIV > Chapter 90B - Motorboats And Other Vessels | | Michigan | Michigan Laws > Chapter 123 > Act 68 of 1957 - Regulation of Houseboats | | Michigan Laws > Chapter 445 > Act 88 of 1989 - Watercraft and Outboard Motor Manufacturers, Distributors, and Dealers | | Michigan Laws > Chapter 570 > Act 59 of 1864 - Lien On Watercraft | | Michigan Laws > Chapter 750 > Act 328 of 1931 > Chapter XV - Boats and Navigation | | Minnesota | Minnesota Statutes Chapter 86B - Water Safety, Watercraft, and Watercraft Titling | | Missouri | Missouri Laws > Title XIX > Chapter 306 - Watercraft Regulation and Licensing--State Water Patrol | | Nevada | Nevada Revised Statutes > Chapter 488 - Watercraft | | New Hampshire | New Hampshire Revised Statutes > Chapter 270-A - Use Of Houseboats | | New Hampshire Revised Statutes > Chapter 270-B - Abandoned Boats | | New Hampshire Revised Statutes > Chapter 270-D - Boating And Water Safety On New Hampshire Public Waters | | New Hampshire Revised Statutes > Chapter 270-E - Vessel Registration And Numbering | | New Mexico | New Mexico Statutes Chapter 66 > Article 12 - Boating | | New Mexico Statutes Chapter 66 > Article 13 - Boating While Intoxicated | | New York | New York Laws - General Business > Article 38 - Vessel Dealer Agreements | | New York | New York Laws > General Business > Article 38 - Vessel Dealer Agreements | | North Carolina | North Carolina General Statutes Chapter 75A - Boating and Water Safety | | North Dakota | North Dakota Code > Chapter 20.1-13 - Boating Regulation | | North Dakota Code > Chapter 20.1-13.1 - Intoxication Testing of Boat Operators | | North Dakota Code > Chapter 20.1-17 - Aquatic Nuisance Species | | Ohio | Ohio Code > Title 15 > Chapter 1547 - Watercraft And Waterways | | Ohio Code > Title 15 > Chapter 1548 - Watercraft Certificates Of Title | | Ohio Code > Title 45 > Chapter 4585 - Actions Relating To Watercraft | | Oregon | Oregon Statutes > Title 61 - Small Watercraft | | Rhode Island | Rhode Island General Laws > Chapter 46-8. Registration of Outboard Motors | | Rhode Island General Laws > Chapter 46-9. Pilots – Rhode Island Sound, Narragansett Bay, Sakonnet River, and Tributaries | | Rhode Island General Laws > Chapter 46-9.1. Pilots–Block Island Sound | | Rhode Island General Laws > Chapter 46-22. Regulation of Boats | | Rhode Island General Laws > Chapter 46-22.1. Uniform Boat Title Act | | Rhode Island General Laws > Chapter 46-22.2. Alcohol Boating Safety Act | | Rhode Island General Laws > Chapter 46-27. Personal Watercraft Safety Act | | South Carolina | South Carolina Code > Title 29 > Chapter 9 - Liens On Ships And Vessels | | South Carolina Code > Title 50 > Chapter 21 - Equipment And Operation Of Watercraft | | South Carolina Code > Title 50 > Chapter 23 - Watercraft And Outboard Motors | | South Carolina Code > Title 50 > Chapter 25 - Boating And Surfing At Particular Localities | | South Dakota | South Dakota Laws > Title 32 > Chapter 03A - Title, Registration And Taxation Of Boats | | South Dakota Laws > Title 32 > Chapter 07B - Regulation Of Boat Dealers | | South Dakota Laws > Title 42 > Chapter 8 - Watercraft | | Tennessee | Tennessee Code > Title 69 > Chapter 9 - Boating Regulation | | Texas | Texas Civil Statutes > Title 132 > Chapter 19 - Boat Or Motor Manufacturers, Distributors, And Dealers | | Utah | Utah Code > Title 73 > Chapter 18 - State Boating Act | | Utah Code > Title 73 > Chapter 18 - Boating - Litter and Pollution Control | | Utah Code > Title 73 > Chapter 18 - Water Safety | | Utah Code > Title 73 > Chapter 18 - Financial Responsibility of Motorboat Owners and Operators Act | | Vermont | Vermont Statutes > Title 25 > Chapter 1 - Operation of Vessels | | Virginia | Virginia Code Title 29.1 > Chapter 7 - Boating Laws | | Virginia Code Title 29.1 > Chapter 8 - Watercraft Dealer Licensing Act | | Virginia Code Title 62.1 > Chapter 18 - Protection of Aids to Navigation | | Wisconsin | Wisconsin Statutes > Chapter 30 > Subchapter V - Regulation Of Boating |
 |
Email
Print