(a) THC determination and initial THC/CH4 contamination corrections. (1) If we require you to determine THC emissions, calculate xTHC[THC-FID]cor using the initial THC contamination concentration xTHC[THC-FID]init from § 1065.520 as follows:

Example: xTHCuncor = 150.3 µmol/molxTHCinit = 1.1 µmol/molxTHCcor = 150.3—1.1xTHCcor = 149.2 µmol/mol

(2) For the NMHC determination described in paragraph (b) of this section, correct xTHC[THC-FID] for initial THC contamination using Eq. 1065.660-1. You may correct xTHC[NMC-FID] for initial contamination of the CH4 sample train using Eq. 1065.660-1, substituting in CH4 concentrations for THC.

(3) For the NMNEHC determination described in paragraph (c) of this section, correct xTHC[THC-FID] for initial THC contamination using Eq. 1065.660-1. You may correct xTHC[NMC-FID] for initial contamination of the CH4 sample train using Eq. 1065.660-1, substituting in CH4 concentrations for THC.

(4) For the CH4 determination described in paragraph (d) of this section, you may correct xTHC[NMC-FID] for initial THC contamination of the CH4 sample train using Eq. 1065.660-1, substituting in CH4 concentrations for THC.

(5) You may calculate THC as the sum of NMHC and CH4 if you determine CH4 with an FTIR as described in paragraph (d)(2) of this section and NMHC with an FTIR using the additive method from paragraph (b)(4) of this section.

(6) You may calculate THC as the sum of NMNEHC, C2H6, and CH4 if you determine CH4 with an FTIR as described in paragraph (d)(2) of this section, C2H6 with an FTIR as described in paragraph (e) of this section, and NMNEHC with an FTIR using the additive method from paragraph (c)(3) of this section.

(b) NMHC determination. Use one of the following to determine NMHC concentration, xNMHC:

(1) If you do not measure CH4, you may omit the calculation of NMHC concentrations and calculate the mass of NMHC as described in § 1065.650(c)(5).

(2) For nonmethane cutters, calculate ?NMHC using the nonmethane cutter’s methane penetration fraction, PFCH4[NMC-FID], and the ethane response factor penetration fraction, RFPFC2H6[NMC-FID], from § 1065.365, the THC FID’s methane response factor, RFCH4[THC-FID], from § 1065.360, the initial THC contamination and dry-to-wet corrected THC concentration, ?THC[THC-FID]cor, as determined in paragraph (a) of this section, and the dry-to-wet corrected methane concentration, ?THC[NMC-FID]cor, optionally corrected for initial THC contamination as determined in paragraph (a) of this section.

(i) If you need to account for penetration fractions determined as a function of molar water concentration, use Eq. 1065.660-4. Otherwise, use the following equation for penetration fractions determined using an NMC configuration as outlined in § 1065.365(d):

Where:xNMHC = concentration of NMHC.xTHC[THC-FID]cor = concentration of THC, initial THC contamination and dry-to-wet corrected, as measured by the THC FID during sampling while bypassing the NMC.xTHC[NMC-FID]cor = concentration of THC, initial THC contamination (optional) and dry-to-wet corrected, as measured by the NMC FID during sampling through the NMC.RFCH4[THC-FID] = response factor of THC FID to CH4, according to § 1065.360(d).RFPFC2H6[NMC-FID] = nonmethane cutter combined ethane response factor and penetration fraction, according to § 1065.365(d).Example: xTHC[THC-FID]cor = 150.3 µmol/molxTHC[NMC-FID]cor = 20.5 µmol/molRFPFC2H6[NMC-FID] = 0.019RFCH4[THC-FID] = 1.05xNMHC = 131.4 µmol/mol

(ii) Use the following equation for penetration fractions determined using an NMC configuration as outlined in § 1065.365(e):

Where:xNMHC = concentration of NMHC.xTHC[THC-FID]cor = concentration of THC, initial THC contamination and dry-to-wet corrected, as measured by the THC FID during sampling while bypassing the NMC.PFCH4[NMC-FID] = nonmethane cutter CH4 penetration fraction, according to § 1065.365(e).xTHC[NMC-FID]cor = concentration of THC, initial THC contamination (optional) and dry-to-wet corrected, as measured by the THC FID during sampling through the NMC.PFC2H6[NMC-FID] = nonmethane cutter ethane penetration fraction, according to § 1065.365(e).Example: xTHC[THC-FID]cor = 150.3 µmol/molPFCH4[NMC-FID] = 0.990xTHC[NMC-FID]cor = 20.5 µmol/molPFC2H6[NMC-FID] = 0.020xNMHC = 132.3 µmol/mol

(iii) Use the following equation for penetration fractions determined using an NMC configuration as outlined in § 1065.365(f) or for penetration fractions determined as a function of molar water concentration using an NMC configuration as outlined in § 1065.365(d):

Where:xNMHC = concentration of NMHC.xTHC[THC-FID]cor = concentration of THC, initial THC contamination and dry-to-wet corrected, as measured by the THC FID during sampling while bypassing the NMC.PFCH4[NMC-FID] = nonmethane cutter CH4 penetration fraction, according to § 1065.365(f).xTHC[NMC-FID]cor = concentration of THC, initial THC contamination (optional) and dry-to-wet corrected, as measured by the THC FID during sampling through the NMC.RFPFC2H6[NMC-FID] = nonmethane cutter CH4 combined ethane response factor and penetration fraction, according to § 1065.365(f).RFCH4[THC-FID] = response factor of THC FID to CH4, according to § 1065.360(d).Example: xTHC[THC-FID]cor = 150.3 µmol/molPFCH4[NMC-FID] = 0.990xTHC[NMC-FID]cor = 20.5 µmol/molRFPFC2H6[NMC-FID] = 0.019RFCH4[THC-FID] = 0.980xNMHC = 132.5 µmol/mol

(3) For a GC-FID or FTIR, calculate ?NMHC using the THC analyzer’s methane response factor, RFCH4[THC-FID], from § 1065.360, and the initial THC contamination and dry-to-wet corrected THC concentration, ?THC[THC-FID]cor, as determined in paragraph (a) of this section as follows:

Where:xNMHC = concentration of NMHC.xTHC[THC-FID]cor = concentration of THC, initial THC contamination and dry-to-wet corrected, as measured by the THC FID.RFCH4[THC-FID] = response factor of THC-FID to CH4.xCH4 = concentration of CH4, dry-to-wet corrected, as measured by the GC-FID or FTIR.Example:

xTHC[THC-FID]cor = 145.6 µmol/molRFCH4[THC-FID] = 0.970xCH4 = 18.9 µmol/molxNMHC = 145.6?0.970 · 18.9xNMHC = 127.3 µmol/mol

(4) For an FTIR, calculate ?NMHC by summing the hydrocarbon species listed in § 1065.266(c) as follows:

Where:?NMHC = concentration of NMHC.?HCi = the C1-equivalent concentration of hydrocarbon species i as measured by the FTIR, not corrected for initial contamination.?HCi-init = the C1-equivalent concentration of the initial system contamination (optional) of hydrocarbon species i, dry-to-wet corrected, as measured by the FTIR.Example: ?C2H6 = 4.9 µmol/mol?C2H4 = 0.9 µmol/mol?C2H2 = 0.8 µmol/mol?C3H8 = 0.4 µmol/mol?C3H6 = 0.5 µmol/mol?C4H10 = 0.3 µmol/mol?CH2O = 0.8 µmol/mol?C2H4O = 0.3 µmol/mol?CH2O2 = 0.1 µmol/mol?CH4O = 0.1 µmol/mol?NMHC = 4.9 + 0.9 + 0.8 + 0.4 + 0.5 + 0.3 + 0.8 + 0.3 + 0.1 + 0.1?NMHC = 9.1 µmol/mol

(c) NMNEHC determination. Use one of the following methods to determine NMNEHC concentration, xNMNEHC:

(1) Calculate xNMNEHC based on the test fuel’s ethane content as follows:

(i) If the content of your test fuel contains less than 0.010 mol/mol of ethane, you may omit the calculation of NMNEHC concentration and calculate the mass of NMNEHC as described in § 1065.650(c)(6)(i).

(ii) If the content of your fuel test contains at least 0.010 mol/mol of ethane, you may omit the calculation of NMNEHC concentration and calculate the mass of NMNEHC as described in § 1065.650(c)(6)(ii).

(2) For a GC-FID, NMC FID, or FTIR, calculate ?NMNEHC using the THC analyzer’s methane response factor, RFCH4[THC-FID], and ethane response factor, RFC2H6[THC-FID], from § 1065.360, the initial contamination and dry-to-wet corrected THC concentration, ?THC[THC-FID]cor, as determined in paragraph (a) of this section, the dry-to-wet corrected methane concentration, ?CH4, as determined in paragraph (d) of this section, and the dry-to-wet corrected ethane concentration, ?C2H6, as determined in paragraph (e) of this section as follows:

Where:?NMNEHC = concentration of NMNEHC.?THC[THC-FID]cor = concentration of THC, initial THC contamination and dry-to-wet corrected, as measured by the THC FID.RFCH4[THC-FID] = response factor of THC-FID to CH4.?CH4 = concentration of CH4, dry-to-wet corrected, as measured by the GC-FID, NMC FID, or FTIR.RFC2H6[THC-FID] = response factor of THC-FID to C2H6.?C2H6 = the C1-equivalent concentration of C2H6, dry-to-wet corrected, as measured by the GC-FID or FTIR.Example: ?THC[THC-FID]cor = 145.6 µmol/molRFCH4[THC-FID] = 0.970?CH4 = 18.9 µmol/molRFC2H6[THC-FID] = 1.02?C2H6 = 10.6 µmol/mol?NMNEHC = 145.6?0.970 · 18.9?1.02 · 10.6?NMNEHC = 116.5 µmol/mol

(3) For an FTIR, calculate xNMNEHC by summing the hydrocarbon species listed in § 1065.266(c) as follows:

Where:xNMNEHC = concentration of NMNEHC.xHCi = the C1-equivalent concentration of hydrocarbon species i as measured by the FTIR, not corrected for initial contamination.xHCi-init = the C1-equivalent concentration of the initial system contamination (optional) of hydrocarbon species i, dry-to-wet corrected, as measured by the FTIR.Example: xC2H4 = 0.9 µmol/molxC2H2 = 0.8 µmol/molxC3H8 = 0.4 µmol/molxC3H6 = 0.5 µmol/molxC4H10 = 0.3 µmol/molxCH2O = 0.8 µmol/molxC2H4O = 0.3 µmol/molxC2H2O2 = 0.1 µmol/molxCH4O = 0.1 µmol/molxNMNEHC = 0.9 + 0.8 + 0.4 + 0.5 + 0.3 + 0.8 + 0.3 + 0.1 + 0.1xNMNEHC = 4.2 µmol/mol

(d) CH4 determination. Use one of the following methods to determine methane concentration, ?CH4:

(1) For nonmethane cutters, calculate ?CH4 using the nonmethane cutter’s methane penetration fraction, PFCH4[NMC-FID], and the ethane response factor penetration fraction, RFPFC2H6[NMC-FID, from § 1065.365, the THC FID’s methane response factor, RFCH4[THC-FID], from § 1065.360, the initial THC contamination and dry-to-wet corrected THC concentration, ?THC[THC-FID]cor, as determined in paragraph (a) of this section, and the dry-to-wet corrected methane concentration, ?THC[NMC-FID]cor, optionally corrected for initial THC contamination as determined in paragraph (a) of this section.

(i) If you need to account for penetration fractions determined as a function of molar water concentration, use Eq. 1065.660-11. Otherwise, use the following equation for penetration fractions determined using an NMC configuration as outlined in § 1065.365(d):

Where:xCH4 = concentration of CH4.xTHC[NMC-FID]cor = concentration of THC, initial THC contamination (optional) and dry-to-wet corrected, as measured by the NMC FID during sampling through the NMC.xTHC[THC-FID]cor = concentration of THC, initial THC contamination and dry-to-wet corrected, as measured by the THC FID during sampling while bypassing the NMC.RFPFC2H6[NMC-FID] = the combined ethane response factor and penetration fraction of the nonmethane cutter, according to § 1065.365(d).RFCH4[THC-FID] = response factor of THC FID to CH4, according to § 1065.360(d).Example: xTHC[NMC-FID]cor = 10.4 µmol/molxTHC[THC-FID]cor = 150.3 µmol/molRFPFC2H6[NMC-FID] = 0.019RFCH4[THC-FID] = 1.05xCH4 = 7.69 µmol/mol

(ii) Use the following equation for penetration fractions determined using an NMC configuration as outlined in § 1065.365(e):

Where:xCH4 = concentration of CH4.xTHC[NMC-FID]cor = concentration of THC, initial THC contamination (optional) and dry-to-wet corrected, as measured by the NMC FID during sampling through the NMC.xTHC[THC-FID]cor = concentration of THC, initial THC contamination and dry-to-wet corrected, as measured by the THC FID during sampling while bypassing the NMC.PFC2H6[NMC-FID] = nonmethane cutter ethane penetration fraction, according to § 1065.365(e).RFCH4[THC-FID] = response factor of THC FID to CH4, according to § 1065.360(d).PFCH4[NMC-FID] = nonmethane cutter CH4 penetration fraction, according to § 1065.365(e).Example: xTHC[NMC-FID]cor = 10.4 µmol/molxTHC[THC-FID]cor = 150.3 µmol/molPFC2H6[NMC-FID] = 0.020RFCH4[THC-FID] = 1.05PFCH4[NMC-FID] = 0.990xCH4 = 7.25 µmol/mol

(iii) Use the following equation for penetration fractions determined using an NMC configuration as outlined in § 1065.365(f) or for penetration fractions determined as a function of molar water concentration using an NMC configuration as outlined in § 1065.365(d):

Where:xCH4 = concentration of CH4.xTHC[NMC-FID]cor = concentration of THC, initial THC contamination (optional) and dry-to-wet corrected, as measured by the NMC FID during sampling through the NMC.xTHC[THC-FID]cor = concentration of THC, initial THC contamination and dry-to-wet corrected, as measured by the THC FID during sampling while bypassing the NMC.RFPFC2H6[NMC-FID] = the combined ethane response factor and penetration fraction of the nonmethane cutter, according to § 1065.365(f).PFCH4[NMC-FID] = nonmethane cutter CH4 penetration fraction, according to § 1065.365(f).RFCH4[THC-FID] = response factor of THC FID to CH4, according to § 1065.360(d).Example: xTHC[NMC-FID]cor = 10.4 µmol/molxTHC[THC-FID]cor = 150.3 µmol/molRFPFC2H6[NMC-FID] = 0.019PFCH4[NMC-FID] = 0.990RFCH4[THC-FID] = 1.05xCH4 = 7.78 µmol/mol

(2) For a GC-FID or FTIR, ?CH4 is the actual dry-to-wet corrected methane concentration as measured by the analyzer.

(e) C2H6 determination. For a GC-FID or FTIR, ?C2H6 is the C1-equivalent, dry-to-wet corrected ethane concentration as measured by the analyzer.

[76 FR 57462, Sept. 15, 2011, as amended at 81 FR 74184, Oct. 25, 2016; 86 FR 34566, June 29, 2021; 88 FR 4686, Jan. 24, 2023]